Smart cutter 1 4 8 serial number how to#
Smart cutter 1 4 8 serial number install#
Smart cutter 1 4 8 serial number driver#
Smart cutter 1 4 8 serial number software#
Smart cutter 1 4 8 serial number download#

Smart cutter 1 4 8 serial number driver#

Once done, you should see this dialog box saying that the driver installation is a success.

If prompted with вЂњDo you want to allow this app from an unknown publisher to make changes to your device?вЂќ.

Launch вЂDrvInstallerвЂќ if you are on a computer with 32-Bit/x86 Windows, or вЂњDrvInstaller_ењ†4вЂќ, if you are on a 64-Bit/ењ†4 Windows.

On your computer, navigate to the вЂњStep 1вЂќ folder.

Step 1 is a basic installation of the WTPTP Driver in your computer. This contains six folders, Starting from вЂњStep 1вЂќ all the way through вЂњStep 6вЂі.

Smart cutter 1 4 8 serial number download#

Download and extract the files you will need in order to do this tutorial.

You will see them in the batteryвЂ™s housing, like the one pictured below: To see the IMEI and the MAC address, remove the back cover of the device and lightly remove the battery.

Write down or take a photo of the IMEI and the MAC address of your device, you will need this later.

Preparation to Unlock your Evoluzn FX-PR3L

Smart cutter 1 4 8 serial number software#

Here is the link to download all the software and files from this tutorial: п»ї Download Software to Unlock the Smart LTE Pocket WiFi (Evoluzn FX-PR3L) This guide will work up and beyond firmware V13.ДЇor those who want a video version of this guide, please watch below. Note that this does not require disassembling the device. This guide will help you unlock your Evoluzn FX-PR3L which will allow you to use any SIM cards, provided that both the device and network (carrier)В use the same frequencies.

Smart cutter 1 4 8 serial number how to#

How to Unlock Smart LTE Pocket WiFi (Evoluzn FX-PR3L) Cable Unlock, Evoluzn, Smart Bro You can easily purchase one from any store near you, but for the convenience they offer, they might come a little bit pricey. Range extenders, as the term defines, вЂ extendвЂ™ your wifiвЂ™s range.

Smart cutter 1 4 8 serial number install#

If you donвЂ™t want to go through the hardware DIY, you can ask your internet service provider if your Wifi Modem has the capability of connecting to a вЂњrange extender.вЂќ Range extenders look like small wifi boxes with external antennas and you can install as many as you can to areas where you have poor wifi strength or none at all. There you go! Your very own DIY external antennas for a better wifi signal strength! If you want to use this without the outdoor antenna, you could purchase an external SMA antenna (as shown in the picture below) and hook it up to the modem, or open the modem again, and connect back the internal antennas. Your mileage may vary, depending on your area.

Turn on the modem and see the improved reception.

Put the cover back, and snap it in place.

It doesnвЂ™t matter which one is which you connect them to.

Connect u.FL connectors onto the motherboard (where you disconnected the internal antennas from back in step 5).

DonвЂ™t forget to install the nuts afterward.

Insert each SMA connectors on each hole.

Loosen the nut on the SMA to u.FL connector and install each one onto the holes.

Start out with the 3/16 bit on each, then finish them off with the 1/4 bit also on both.

Once the cover is off, disconnect the two antennas (circled in red) gently.

If youвЂ™re having trouble sliding the plastic through, yank out the cover a little bit to ease the plastic through.

Once both the cutter and thin plastic are both inserted, slide the thin plastic throughout the perimeter of the modem.

Grab a thin plastic (guitar pick, gift card, etc), and insert it next to the cutter. Insert the cutter in the middle to avoid damage to the internal antennas, just in case you want to use it again the future.

Take the box cutter and slowly insert it into the left side modem, when doing so, make sure it face down at a 45-degree angle.

Use the ruler and marker to write lines on the back of the modem as shown in the picture.

Thin plastic (like a guitar pick or gift card).

Marker (any color will do, as long as you can easily see it).

Antenna SMAWiFi Pigtail Cable IPX to SMA (в‚±99.00 on Lazada).

Things you need to buy/required for this modification: There is also a video version of this guide. There are a number of factors that may affect wifi signal strength (1) thick walls, (2) microwave oven, and (3) actual distance from the router/modem. But it may or may not be the same for you, it depends on your area.

In my case, this modification boosted my signal indoors. It is up to you whether to proceed or not.Дisclaimer: We are not responsible if things go wrong.ДЄlso, your mileage may vary. It is essentially the same modem, just a different brand.В Be warned: doing this notification will surely VOID your warranty. This will also work on the PLDT Prepaid Home WiFi. How to add External Outdoor Antenna to Evoluzn FX-ID3 Modem Antenna Hack, Evoluzn, Smart BroДЄre you getting a weak signal from your Smart Bro Prepaid Home WiFi? ThereвЂ™s a way to fix it!Д«oost the signal by adding antenna correctors and outdoor antennas!